FANDOM


Introduction Edit

My goal in this project was to build a traditional swivel-per-loop garland but with all metal moving parts. At no point does fabric wear against metal nor is the fabric of any loop interrupted by metal. I wanted a large loop garland that would make bubbles suitable for people to do bubble-in-bubble with. IMO, the maximum practical garland loop size is about 255 mm (10 inches) and my favorite material for good bubble stream duration is 3x braided Bed Bath & Beyond twine.

Materials Edit

Treated and braided Bed Bath & Beyond cooking twine (8-strand)

Cotton household string

#28 Artistic Wire brand permanently colored wire

#6-#8 mercerized crochet cotton

This is my wick material. Its ends are bound with a bit of cotton household string to keep them from unraveling as I work.

3xBBBEndsBound

3x braided BB&B cooking twine with ends bound

Tools Edit

Scissors

Small wire cutters

Small pliers or hemostats

Hot glue and gun

Procedures Edit

Joining the cord ends Edit

Cut a 50 mm piece of wire.

02 Cut50mmWire

Cut a 50 mm piece of wire

Feed the wire through a swivel. Note how the swivel is shaped like a bullet, with a pointed and a blunt end. Feed the wire through the ring of the blunt end. We'll be applying glue near this end and don't want it to get into the swiveling mechanism at the pointed end.

03 FeedWireThru1stSwvl

Feed the wire through a swivel

Bend the wire at its halfway point around the swivel.

04 BendWireOverSwvl

Bend the wire in half through the swivel

05 BendWireOverSwvl2

Wire bent in half on the swivel

Place the wire and swivel on one of the braided ends, with the wire loop extending about 1 mm beyond that end. Note how the overhand knot of the braid binder string is on the opposite side. This makes the following steps a little easier.

06 PositWireSwvlNearTip

Position the wire and swivel near one of the cord

Cut a piece of crochet cotton for the whipping. I used 60 cm (24") pieces. You might want to use longer ones until you have more practice.

Lay the whipping string across the wire about 12 mm (1/2") from the cord end.

07 Whip1PositStr

Prepare for the 1st whipping

Tie an overhand knot on the opposite side of the cord from the wire and pull it tight.

09 Whip1-1stKnot2

Anchor knot for the 1st whipping, outside

08 Whip1-1stKnot

Anchor knot for the 1st whipping, inside

Bend the wire ends over that whipping anchor and toward the cord end.

10 Whip1BendWire

Bend the wire ends over the anchor

11 Whip1WireBent

Wire bent over the anchor

Place the opposite end of the cord on top of the first. Make sure to follow the braid so there are no twists in it.

12 Whip1PositCheck

Place the wire between the cord ends

Bring the ends of the whipping string over the second cord and and tie an overhand knot. Make sure the 2 cord ends align as closely as possible before pulling that knot tight.

13 Whip1-2ndKnot

Bring the 2nd cord end into the whipping

Note the directions that the string's ends exit from the knot. One will be angled toward the cord's ends. Form a loop with that end that reaches beyond the string's connector's loop.

14 Whip1FormPullThru

Form the whipping's pull-through loop

Grasp the cord's ends and that loop in one hand. The free end of the string will be angled away from the cord's ends and toward one side of the piece. Wrap that piece around the cord's ends, continuing in the direction that it exits from the knot. With each revolution around the cord's ends, wrap the string a little closer to the cord's ends, as pictured.

16 Whip1Wrap2

Grasp for start of whipping

15 Whip1Wrap1

Start the whipping

17 Whip1Wrap3

Continue 1st part of whipping

Before the wrappings reach the braid binder strings, get a new grasp that exposes the ends and the pull-through loop.

18 Whip1Wrap4

New grip for completing whipping

Pick off those binder strings with your fingers or any convenient tool.

19 Whip1PopKeepers

Braid binder strings removed

Continue wrapping the connection until you are about 2 mm from the cord's ends, and at a point just below the loop you formed earlier. Hold the wrapping string at that point with a thumb and forefinger.

20 Whip1WrapFinHold

Prepare for whipping completion

Pass the lead end of the whipping string through the loop. Be careful to keep the swivel itself from feeding through this loop.

21 Whip1Fin1

Pass the whipping string's lead end through the loop

Find the other (tail) end of the wrapping string (in your palm) and pull on it until the loop closes, but not any farther.

22 Whip1Fin2

Locate the whipping's tail

23 Whip1Fin3

Pull the whipping's tail to close the loop on the lead end

24 Whip1Fin4

Grasp the knot firmly at that point (where the loop has just closed on that string) and with your other hand, pull the lead end of the whipping string away from the knot and perpendicular to it, to take up any slack. Loosen your grip and rotate the knot as needed to allow slack to be taken in.

25 Whip1Fin5

Take up slack in the lead end of the whipping

26 Whip1Fin6

Grasp the entire whipping firmly and gradually pull on the whipping's tail end. You will be able to feel the end loop being pulled into the body of the knot. Stop pulling when the loop seems to have reached the center of the knot, or until it has passed beneath at least 3 windings. Trim the string ends.

27 Whip1Fin7

Pull the end loop into the whipping's body

28 Whip1Fin8

Finished whipping before trimming ends

Besides increasing the 'foreverness' of this connection, hot-gluing it adds other benefits. The glue is less absorbent than cotton so it reduces the potential for the bubble streams joining together.

32 Whip1Glue1

Hot glue coat the cord end whipping

To finish the glue job, place a bead of glue around the exposed tips of the cords, wet your thumb and forefinger, and roll those tips into a sort of bullet shape. This helps to reduce hang-ups. Excess glue on the swivel's ring can be picked off with tweezers as needed.

33 Whip1Glue2

Apply glue around the cord tips

34 Whip1Glue3

Wet fingers for shaping glue

35 Whip1GlueCleanSwvl

Roll the cord tips into a bullet shape while the glue is still warm.

The finished end connection. Repeat for every loop.

36 Whip1Done

Finished end connection

Make the corner connections and build each garland half Edit

This type of garland design requires an even number of loops. You build 2 half garlands and then join them together with each half's end connections pointing toward the poles' tips, and its corner connections pointing toward its center.

Mark the positions of each loop's corner connection. Make sure it's on the outer side of the loop's braid. See my Garland Loop Sizing Calculations article for tips on garland loop sizing.

29 MeasCrnr

Measure the corner's position

31 MeasCrnr3

Marking a corner connection

Cut a 30 mm (1 1/8") wire for the corner connection.

38 Cut30mmWire

Cut wire for the corner connection

Bend the wire at its center, making a long narrow "U" shape. Precision helps at this point.

40 CrnrWireBendCtr
41 CrnrWireBend1

Bend about 2mm of the wire loop's tip upwards at a 90 degree angle.

42 CrnrWireBend1.5

Bend the tip of the wire up

43 CrnrWireBend2

Also bend wire tip ends up, at about 3-4 mm from their ends.

44 CrnrWireBend4

Bend wire tips' ends up

45 CrnrWireBend5

Corner wire shaped for whipping

Feed a cord end swivel through this corner connection wire.

46 CrnrWireOnSwvl

Feed the wire through an and connection's swivel

Place the swivel's ring at the spot marked for the corner, with the corner wire's ends pointing toward the top-string (shorter section) and away from the bottom.

47 CrnrPositAssy1

Position assembly for whipping

Cut a string for whipping and place it across the wire, near the bend by its ends.

48 Whip2PoistStr

Position string for whipping

Tie an overhand knot on the opposite side of the braid from the wire.

49 Whip2Knot1

First corner know, inside of braid

50 Whip2Knot1-1

First corner know, outside of braid

Bend the wire ends over that whipping anchor string and toward the wire's loop end.

51 Whip2FoldWire

Bend the wire over the string

Bring the whipping string's ends up over that bend and tie an overhand knot near but above the bend. Pull it tight.

52 Whip2Knot2

Make a second overhand knot above the wire

Continue making overhand knots on alternating sides of the braid, working your way toward the wire's loop end. You're essentially making a modified West Country whipping for this connection.

53 Whip2KnotMore

Continue with a West Country whipping toward the wire's loop

When the whippings have reached the bend at the wire's loop end, make one more overhand knot past that wire loop on the braid's top, and finish the whipping with a square (reef) knot. (Make an overhand knot in the opposite direction of the previous one.)

54 Whip2KnotFin1

Make one more knot beyond the loop end on the braid's top

55 Whip2KnotFin2

Finish the whipping with a square knot

Trim the whipping's ends but not too closely. Leave some ears on it. With time, the ends will expand and "lock" the knot.

56 Whip2KnotFin3

Trim string but not too close

57 Whip2KnotFin4

Knot with ears

The finished connection will look like this.

FinishedConnect2

Finished corner connection

When you've finished the first half of the garland's loops, add one more corner connection and swivel its end loop, put that half aside, and make the corner connections for the second half. After that, the 2 halves are ready to connect.

58 CtrB4Join

The 2 garland halves, ready to connect

Connect the halves and add the leaders Edit

Even with 2 swivels and a split ring separating the 2 halves, the bubble streams of the 2 innermost loops are likely to join. I used yet another swivel to increase the separation but you might also use a short length of strong fishing line.

59 CtrConnect

Center connection

60 Leaders

Leaders

Performance characteristics Edit

Design advantages Edit

An advantage to this design is that the loops lay relatively flat as you lift its 2 halves from the solution.

63 LayOnLift

Loops lay flat on the lift

The wire corner "staples" keep the braid's top and bottom pointed in a favorable way as they exit the corner connection. Together with the bullet-shaped cord end joints, this reduces hang-ups.

64 10inAtWork

The overall design avoids loop hangups

Being such large loops, it only takes a little wind or waving to push out a lot of big bubbles. It's great for times when there's little or no wind. Its only downsides are that it's rather heavy and uses a lot of solution.

Combating combined bubble streams Edit

In an effort to minimize how often its bubble streams combined, I applied some hot glue to the outer surface of the braid near the corners. It worked but had 2 big disadvantages. Its loops no longer laid as flat on the lift. The wind had more of a chance to start producing bubbles prematurely. It also experienced more hang-ups. I had to use a hot iron and paper toweling to melt down and mop up as much of that glue as I could.

61 GlueCrnr1

Combined bubble streams can also be minimized by using a minimal amount of polymer (PEO, HEC, guar, etc). Extra polymer is wasted on garlands anyway. See this Wiki's Recipe Pages for recommendations on polymer usage.

Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.